What wall foam insulation includes
- Checking the wall's condition and identifying cracks and damp before spraying begins
- Treating visible cracks, cleaning the surface and preparing it to receive the foam properly
- Spraying polyurethane foam onto the wall so it expands into a seamless layer with no joints
- Covering neighbouring areas that should not receive foam during spraying
- Applying an external finish coat over the foam to protect it from ultraviolet light
- Answering your questions about wall foam insulation before the work starts
From your call to an insulated wall
- 1
Tell us what you see
Call or message us on WhatsApp; describe which walls feel hot from inside and whether there is any cracking or damp.
- 2
Preparing the wall surface
Before spraying, surfaces are cleaned, cracks are treated and areas not being sprayed are covered. Foam cannot substitute for a sound surface, and the layer will not hold on a failing wall.
- 3
Spraying the foam onto the wall
Polyurethane foam is sprayed onto the wall; it expands in the air and covers the surface in a seamless layer with no joints, blocking heat from travelling through the wall.
- 4
The finish coat over the foam
Foam is naturally vulnerable to ultraviolet light and needs protection. A finish coat such as render or external cladding is applied over it to protect the material and preserve the wall's appearance.
Wall insulation done with care
- We prepare the wall before spraying, not after
- The foam covers the wall in a seamless layer with no joints
- Visible cracks are treated before the insulation goes on
- A finish coat is applied to protect the foam from the sun
- We take your request by phone call or WhatsApp message
The service in Ash Shuruq
Homes in a district like Ash Shuruq usually have outer walls facing the sun directly. In hot summer, these walls heat quickly and pass warmth into the rooms, making life inside the home uncomfortable. Small joints or cracks may be there around windows and doors or at the base of the wall where damp gathers from rare rain. Technicians check the wall and ground around it, clean the area, fix any crack or damp, then spray foam in a uniform layer. A clean, dry surface is the foundation for foam to work well.
Ash Shuruq is a district in Al-Ahsa governorate in the Eastern Province, close to Al Muruj, Al Yasmin and Ar Rabie.
Corners and joints around doors and windows need the most care in checking and spraying.
Our portfolio
What our customers say
- ★★★★★
شكراً لخدمتك الجميلة
- ★★★★★
ممتاز والخدمة ان شاء الله تكون قد التوقعات
- ★★★★★
شكرا على التواصل السريع
Reviews are shown as the customers wrote them, in Arabic.
Questions about Wall foam insulation in Ash Shuruq
Yes, spraying foam on a wall from the inside is technically possible and reduces heat reaching the room. Outside insulation is usually more effective, though, because it intercepts heat before the wall absorbs it at all, not after. The choice between the two sides depends on the wall's condition and the building's layout.
Insulating the wall most exposed to direct sun gives a noticeable improvement, because that wall is often the main heat source. The more walls you insulate, the greater the effect on the room temperature. Just tell us which wall bothers you most.
Polyurethane foam is naturally water-resistant, so it also stops moisture penetrating through the wall alongside its heat-insulating property. However, a wall that already has cracks or damp must be treated before spraying, because the foam does not fix a problem that exists beneath it.
Ultraviolet light damages exposed foam over time: the surface crumbles and the material loses its shape and its properties. A finish coat such as external render or cladding protects the foam from the sun and makes the wall resistant to the elements. This coat is not just decorative; it is an essential part of the system.
Tell us which side of the building the wall faces and whether it is external or internal, whether you notice any cracks, damp or stains in it, and how many rooms feel hot. The more detail you give us, the more clearly we can guide you.
Foam reduces water entering from outside if the spraying is thorough and complete. But large cracks and joints must be repaired before spraying, or the foam will not work well.
Say which rooms feel hottest, which walls you want insulated, whether there are visible damp stains or cracks, and send photos of the walls on WhatsApp.
More services in Ash Shuruq
