What plumbing first-fix includes
- Setting the routes of cold and hot water supply pipes inside walls and floors
- Laying drain pipes and adjusting their falls so water flows without pooling
- Marking drain outlet positions according to the planned sanitary ware layout
- Securing pipes with clips and making joints before burial in wall or floor
- Testing the supply line under pressure before plastering to find any weak joint
- Marking the final connection points for sanitary ware, ready for the finishing stage
From the plan to closing the wall
- 1
Tell us about your project
Call or message us on WhatsApp and tell us the building type, its stage and the rooms to be first-fixed, so we understand what the pipework needs.
- 2
Setting routes and falls
Supply and drain routes are drawn and drain falls are set before any cutting, because the slope of a drain pipe directly affects how well it clears later.
- 3
Laying and securing
Pipes are laid in walls and floors and secured with clips, and joints are made carefully, because a weak joint behind the wall may not show for years.
- 4
Pressure test before closing
Before plastering or casting the floor, the supply line is tested under pressure to confirm the joints are sound. This is the only time a fault can be fixed without demolition.
Correct first-fix prevents demolition later
- We lay the pipes before burial on set routes
- We set the drain falls accurately at this stage
- We run a pressure test before closing the wall or floor
- We take your request by phone call or WhatsApp message
- Reach us by call or WhatsApp message
The service in Ibn Dihman
A home in a place like Ibn Dihman depends on a network of pipes connecting the kitchen, bathroom and tank, and each pipe must run at the right slope to drain water. Joints and connections must be tight, and any weakness in them shows as dampness or leaks after you move in. The first check looks at every route, every slope and every joint, and if we see a weakness we fix it before building over it.
Ibn Dihman is a small settlement in Al-Ahsa governorate in the Eastern Province, close to Muraytibah, Sudah and Al Jishshah.
Adequate slope from the pipe's high point to the drain is checked first, because poor slope collects water and creates pockets of dampness.
Our portfolio
What our customers say
- ★★★★★
شركه ممتازه واشتغلنا معاهم اكثر من مره وجود عاليه ما شاء الله بارك الله فيهم واعمله
- ★★★★★
شكرا على التواصل السريع
- ★★★★★
شركه ممتاز شغلهم كويس ويعطيهم العافيه
Reviews are shown as the customers wrote them, in Arabic.
Questions about Plumbing first-fix in Ibn Dihman
First-fix is when pipes are laid inside walls and floors before plastering and tiling, in a new building or a major renovation. Ordinary plumbing work deals with the visible fittings, taps and sanitary ware after finishing. Each stage has its own requirements and tools.
Because the pressure test reveals any weak joint or fault in the line before the wall is closed. After plastering and tiling, the pipe cannot be reached without demolition. This stage is the only chance to fix a fault without extra cost.
It is very difficult after casting and often requires breaking part of the floor. This is why drain outlet positions are set accurately before casting, based on the planned sanitary ware positions in each room.
The fall matters greatly. Too little and water sits in the pipe, leaving solids that build up into a blockage over time. Too steep and the water runs ahead of solids, which are left behind. Horizontal drain pipes have an accepted fall range that should be followed.
Tell us the building type, the number of floors and the rooms to be first-fixed, and whether it is a new build or a partial renovation. If you have a layout of the planned sanitary ware or the drain outlet positions, mentioning it helps us understand the scope of work. Call or message us on WhatsApp.
They check each pipe route from the tank to the bathroom and kitchen, the slope at every point, and confirm that the joints are tight and hole-free.
The main causes are poor slope, a loose joint or a punctured pipe. A proper check at the start saves you from it.
