Al Raya
Roof heat insulation in Az Zahrah District: The edge of a roof insulated in white beside a building under a clear sky

Roof heat insulation in Az Zahrah District

In Az Zahrah District, flat roofs receive the sun directly, so the top-floor rooms heat up noticeably. Al Raya insulates the roof with polyurethane foam to stop heat transfer into the home.

What the service includes

What roof heat insulation includes

  • Checking the concrete roof condition to identify what needs treating before insulation
  • Finding cracks and joints that need repair before the layer goes on
  • Preparing, cleaning and levelling the surface so the layer bonds properly
  • Applying sprayed polyurethane foam or epoxy coating according to the roof condition
  • Covering edges, joints and the base of the parapet to complete the insulation
  • Treating any water leak found during inspection before the heat insulation is finished
How we work

From your call to an insulated roof

  1. 1

    Tell us what you feel

    Call or message us on WhatsApp and describe which floor gets hot and which rooms are affected, and we will decide with you what needs to be checked.

  2. 2

    We inspect the roof first

    We check the roof condition before anything else, because a roof with cracks or standing water needs waterproofing before the heat-insulating layer goes on.

  3. 3

    We prepare the surface

    The job involves cleaning the surface and levelling what needs levelling, because a layer only works as it should on a clean and ready surface.

  4. 4

    We lay the heat-insulating layer

    We choose between sprayed polyurethane foam and epoxy coating according to the roof condition and what is needed, and we cover the whole area including the edges and joints.

Why Al Raya

An insulated roof makes a difference in the rooms below

  • We inspect the roof before insulating to choose the right layer
  • Polyurethane foam covers edges, joints and corners
  • Epoxy is a hard coating that reflects heat and protects the surface
  • We treat cracks and leaks before the heat-insulating layer goes on
  • We take your request by phone call or WhatsApp message
About the area

The service in Az Zahrah District

Homes in a district like Az Zahrah usually have flat roofs responsible for most heat entry, especially if the roof is uninsulated. The roof typically has a parapet, drains and water tanks, each a joint allowing heat in. Foam is sprayed as one continuous layer covering the whole roof without gaps, greatly reducing how much heat passes inside. Work starts with a check of the roof to ensure it is free of damp and serious cracks.

Az Zahrah District is a district in Al-Ahsa governorate in the Eastern Province, close to Al Jamiyin District, Al Iskan 1st District and Al Hamra 1st District.

The first roof check focuses on joints, cracks and drain areas, as these are the main heat pathways.

Read about Roof heat insulation

Our work

Our portfolio

  • A white roof with an air conditioner and satellite dishes
  • A roof covered in a smooth white insulation layer with a small dome behind it
  • A roof insulated in white under a clear sky
  • A roof covered in white insulation with air conditioners and buildings around it
  • A building roof covered in white insulation
  • A roof covered in white insulation with a worker in the distance
Reviews

What our customers say

  • ★★★★★

    ممتاز والخدمة ان شاء الله تكون قد التوقعات

  • ★★★★★

    شكرا على التواصل وصلو في اسرع وقت ممكن

  • ★★★★★

    شركه ممتاز شغلهم كويس ويعطيهم العافيه

Reviews are shown as the customers wrote them, in Arabic.

Questions

Questions about Roof heat insulation in Az Zahrah District

Heat insulation aims to stop the sun's heat passing from the concrete roof into the rooms below, which shows in the top floor in summer. Waterproofing aims to stop water entering through cracks and joints. A roof often needs both, and inspection decides which comes first.

A layer on its own does not seal cracks; it goes on a ready surface. If the roof has cracks or areas that have held water before, treating them comes before the heat-insulating layer, otherwise the problem stays under the new layer.

Polyurethane foam is a sprayed foam layer that fills edges, corners and joints and insulates well. Epoxy is a resin that is applied as a coat and hardens, reflecting heat and protecting the concrete. Choosing between them depends on the roof condition and what it needs.

Roof heat insulation treats the transfer of heat through the concrete into the rooms below. Wall dampness has its own causes, often water entering through joints or cracks in the wall or roof. Inspection identifies the source of the dampness before any treatment.

Heat insulation suits exposed concrete roofs where heat transfer is the main problem. If the roof has wide cracks, standing water or a badly worn old layer, the work starts with assessing the roof condition and deciding what to treat first before the right heat-insulation method is chosen.

Foam greatly reduces heat transfer, but does not eliminate it entirely, especially at the height of summer. The aim is for the top rooms to stay noticeably cooler than they would be without insulation.

The roof is checked on the first visit to assess its condition and identify areas needing special care, which ensures proper planning for the work.

Sunset over villa roofs and palm trees

Call and we start with the roof

Call or WhatsApp us and describe the roof and the rooms that get hot.

Call nowWhatsApp