What instrument-based leak detection includes
- Scanning the suspect area with a thermal camera to map temperature differences that indicate moisture
- Checking surfaces, walls and ceilings with electronic instruments to measure conductivity and follow the water path
- Reading moisture content in materials with a moisture meter to define the boundaries of the affected zone
- Telling an actual leak apart from condensation and moisture from a different source
- Pinpointing the original entry point, not just the visible mark on the surface
- Documenting the result in a certified report after inspection, stating the position and the cause
From your call to the report
- 1
Tell us what you see
Call or message us on WhatsApp and describe what you see: where it is, when it appeared, and whether it is spreading or changing.
- 2
We scan with camera and instruments
The thermal camera shows the temperature difference between dry and wet areas, and the electronic instruments measure conductivity and follow the water path under the surface.
- 3
We identify the source and cause
We tell a pipe leak from a joint leak or condensation apart, because each needs a different repair, and confusing them causes the fix to fail.
- 4
You receive a certified report
After inspection you receive the result in writing with the leak's location and cause, and you decide the next step based on clear information.
No guessing, no breaking
- Detection with no breaking, using precise instruments
- The thermal camera spots moisture before it spreads
- We tell a leak from condensation with measurable evidence
- Certified report after inspection documents the source and cause
- We take your request by phone call or WhatsApp message
The service in Haradh
A town like Haradh has homes with flat roofs, rooftop tanks and pipes distributed through buildings. Damp appearing on the ceiling or in a wall corner may come from a pipe on the ground floor, from leakage around a rooftop tank, or even from an adjacent wall. Al Raya uses the thermal camera to detect unusual cold spots on surfaces and walls, and the electronic instrument to trace metal pipes and water flow. The technician images each stage to show you exactly where the water is and where it comes from.
Haradh is a town in Al-Ahsa governorate in the Eastern Province, close to Ash Shuruq, Al Ekhaa and Ar Rabie.
A slow leak may escape the eye but the thermal camera scans every surface for water spots and unusual cold zones.
Our portfolio
What our customers say
- ★★★★★
شكراً لخدمتك الجميلة
- ★★★★★
شغلهم كويس وناس ممتازه في اسرع وقت
- ★★★★★
شركه ممتازه واشتغلنا معاهم اكثر من مره وجود عاليه ما شاء الله بارك الله فيهم واعمله
Reviews are shown as the customers wrote them, in Arabic.
Questions about Thermal-camera & electronic leak detection in Haradh
The thermal camera maps the temperature difference that moisture causes at a surface, showing the wet area as cooler or warmer than its surroundings. It does not penetrate thick surfaces and cannot define the full path or size of a leak on its own, which is why it is used with other instruments to confirm the result.
In most cases yes. The electronic instruments measure moisture from the wall's outer surface and follow the water path without breaking it open. In rare cases direct access may be needed, but that comes after the exact position is known, not before.
An electronic detector senses the change in electrical conductivity that water causes in or under a material, and suits tracking a leak across a wide area. A moisture meter reads how much water a specific material such as concrete or plaster has absorbed, and is useful for mapping the exact boundaries of a damp zone.
Not always. The camera locates suspect areas quickly and is a valuable starting point, but the thermal signal may point to where moisture has spread, not to where it entered. Combining it with electronic instruments and a moisture meter gives a more accurate picture.
The report states the leak's position as found by the instruments, the likely cause, and the area affected by moisture. This lets any specialist who comes next start from the right place without repeating the inspection from scratch.
Specify exactly which room and which wall or ceiling, when you first noticed it, whether it grew or stayed the same, and send a very clear photo on WhatsApp with a measurement scale if possible.
A cold spot means water or moisture is concentrated there, either from a direct leak above it or from water sliding toward it from elsewhere. The cold indicates water presence even before visible dampness appears.
More services in Haradh
Thermal-camera & electronic leak detection in nearby areas
