What epoxy tank lining includes
- Checking the inner walls and base to identify cracks and damaged areas before starting
- Emptying the tank and removing sediment and flaking old layers from the entire inner surface
- Treating cracks and joints in the walls and base before the epoxy coat is applied
- Verifying the surface is dry and even before coating so the layer bonds properly
- Applying epoxy to the inner walls and base so it hardens into a smooth, continuous film
- Reviewing the finished layer after hardening and confirming it covers the entire inner surface
From your message to a finished lining
- 1
Describe your tank
Call or message us on WhatsApp and tell us the type of tank, where it sits, and what you notice inside or around it, whether damp marks or cracks.
- 2
Emptying and cleaning
The tank is fully emptied and any sediment or flaking old layers are removed from the walls, because epoxy will not bond to a dirty or loose surface.
- 3
Repairing cracks and preparing the surface
Cracks and joints are repaired before coating, and the surface is checked to be dry and even, because the epoxy layer is only as good as the surface beneath it.
- 4
Applying the epoxy
The epoxy is applied to the inner walls and the base and hardens into a smooth, continuous film that seals the pores and separates the surface from the water.
The tank will be sealed from inside
- Epoxy seals the concrete pores and smooths the surface
- A smooth surface stops sediment sticking to the walls
- We treat cracks before coating, not over them
- Suitable for ground tanks and overhead tanks alike
- We take your request by phone call or WhatsApp message
The service in Government Departments Complex 2nd District
Tanks in homes and buildings in a district like Government Departments Complex 2nd District are exposed to damp and salts from groundwater and heavy irrigation across Al-Ahsa. Rough or old tank walls absorb damp and leave marks on stored water. Inspection begins with the condition of the inner walls, cracks, stains and sediment, then the tank is cleaned carefully and the walls are prepared. Epoxy is applied to a dry surface, forming a barrier that protects the water from the walls.
Government Departments Complex 2nd District is a district in Al-Ahsa governorate in the Eastern Province, close to Al Hamra 1st District, Al Aziziyah 1st District and Al Hamra 2nd District.
White and brown sediment on tank walls points to salts and damp, and is the first thing checked when you call.
Our portfolio
What our customers say
- ★★★★★
شكرا على التواصل السريع
- ★★★★★
شكراً لخدمتك الجميلة
- ★★★★★
شغلهم نظيف وسريعين ومحترمين الله يعطيهم العافيه
Reviews are shown as the customers wrote them, in Arabic.
Questions about Epoxy tank lining in Government Departments Complex 2nd District
Yes, the base is part of the inner surface and it cannot be left untreated while the walls are coated. Water sits on the base and presses into its pores, and a continuous lining stops a leak wherever it tries to get through.
Ordinary paint is a surface coat that peels with constant water contact and does not seal the concrete pores. Epoxy is a resin that reacts, hardens and bonds to the surface, forming a solid film that actually separates the concrete from the water and does not break down easily.
Epoxy bonds to a range of surfaces and is used in concrete, metal and other tanks when the surface is prepared, clean and dry. What changes is how the surface is prepared according to the material, not the principle of applying the coat.
Epoxy bonds to a solid surface, not to water sitting in the concrete pores. If the surface is damp, a gap forms between the coat and the wall that weakens adhesion and leaves the lining prone to blistering and peeling later. Dryness is a requirement, not a precaution.
Yes, the size of the tank does not change how the work is done. Small roof tanks go through daily temperature swings that stress the walls and open fine pores and cracks. An epoxy lining on the inner walls seals those pores and protects the surface whatever the size of the tank.
Yes, the tank must be empty and dry inside, because epoxy is applied to a clean, dry surface. The tank stays empty during the work and for a period until the epoxy hardens fully.
Damp is water that seeps through the walls from outside and leaves marks, and salts are minerals from groundwater. Both affect water taste and purity, and epoxy blocks both from stored water.
More services in Government Departments Complex 2nd District
Epoxy tank lining in nearby areas
