Al Raya
Fibreglass tank lining in Al Shagaibiyah District: Gloved hands repairing a fibreglass tank wall with glass-fibre mat and resin

Fibreglass tank lining in Al Shagaibiyah District

In Al Shagaibiyah District, many homes have fibreglass tanks, and when they leak, repair needs care for their flexible walls. Al Raya treats the inner surface with a strong protective layer, so the tank regains its strength.

What the service includes

What fibreglass tank lining includes

  • Inspecting the inner wall and base after the tank is emptied
  • Locating the cracks and assessing how far the surface layer is damaged
  • Treating the cracks with a flexible resin material that tolerates fibreglass wall movement
  • Preparing and cleaning the inner surface before the new lining is applied
  • Applying the inner lining to the full walls and base of the tank
  • Checking that joints, edges and any weak point on the surface are fully covered
How we work

From your call to a re-lined tank

  1. 1

    Tell us what you notice

    Call or message us on WhatsApp and describe the tank, whether the water level drops, whether you see discolouration or damp below it.

  2. 2

    Inspecting the inner wall

    We empty the tank and inspect the inner wall and base, locating the cracks and assessing how far the surface layer is damaged.

  3. 3

    Treating the cracks and preparing the surface

    The cracks are treated with a flexible resin material that tolerates movement in the fibreglass wall, then the surface is cleaned and prepared before lining.

  4. 4

    Re-lining the inside

    The new lining is applied to the full inner surface once it is ready, covering the walls and the base of the tank.

Why Al Raya

The tank is repaired, not replaced

  • We treat cracks with a material that matches fibreglass flexibility
  • We inspect the inner wall and base before any lining
  • We re-line the full surface, not the crack alone
  • We take your request by phone call or WhatsApp message
  • Reach us by call or WhatsApp
About the area

The service in Al Shagaibiyah District

Fibreglass tanks in homes may develop cracks or small holes from continuous pressure and temperature changes. This cannot be fixed from outside but from the tank's inner surface, because the material is flexible and not rigid. Inspection starts by locating the leak precisely, then the inner surface is cleaned carefully and a protective coating is applied to seal cracks and gaps. The right material and method follow the first inspection of the tank.

Al Shagaibiyah District is a district in Al-Ahsa governorate in the Eastern Province, close to Al-Hofuf, Al Muallimeen District and Historical Center Hafuf District.

Leaks from tank corners and the base are most common, because salts in water and soil speed up material deterioration there.

Read about Fibreglass tank lining

Our work

Our portfolio

  • A worker rolling white insulation coating onto a villa roof
  • Damp stains and damage on a ceiling beside a wall light
  • A hand scraping damp mortar from between small stones on a surface
  • Peeling paint on an exterior wall beside a pipe
  • Cracked and bubbling paint along a wall edge
  • A white roof with an air conditioner and satellite dishes
Reviews

What our customers say

  • ★★★★★

    ممتاز والخدمة ان شاء الله تكون قد التوقعات

  • ★★★★★

    شغلهم نظيف وسريعين ومحترمين الله يعطيهم العافيه

  • ★★★★★

    شركه ممتازه

Reviews are shown as the customers wrote them, in Arabic.

Questions

Questions about Fibreglass tank lining in Al Shagaibiyah District

The clearest signs are a falling water level without use, or damp and a stain below or around the tank. Sometimes the water changes colour or a thin cracked layer peels from the inner wall. Any of these signs calls for an inspection before the damage spreads.

Because a fibreglass wall moves slightly under the weight of water and changes in temperature. If the lining is applied over an open crack, the new layer will crack at that point. The crack is treated with a flexible material that absorbs movement before the full surface is covered.

In many cases yes. A full inner lining covers wide surface damage after the cracks are treated and the wall prepared. This depends on the extent of the damage and the condition of the wall itself, which is why the work always starts with inspecting the inner surface to see what the tank actually needs.

Yes. Concrete is rigid and thick-walled, and its cracks are usually treated with cement-based or rigid resin materials. Fibreglass is thin and flexible, so a rigid filler will separate from the surface at the first movement. Fibreglass cracks need a flexible resin material that suits the nature of the wall.

Tell us the size and position of the tank, whether it is overhead or at ground level, and describe what you see: whether the water level drops, whether there is damp below, whether you can see a crack or peeling on the inner wall. The clearer your description, the better we can judge what the tank needs before we arrive.

A photo helps but direct inspection of the tank is necessary. We must see the leak location inside and outside to understand the problem, especially if cracks are very fine.

Growing damp patches around the tank, musty or strange smells, and a noticeable drop in water level. If you see any of these signs, contact us immediately on WhatsApp.

Nearby areas

Fibreglass tank lining in nearby areas

Sunset over villa roofs and palm trees

Call and we inspect your tank

WhatsApp or call us and describe what you see in your fibreglass tank.

Call nowWhatsApp