From your call to the work
- 1
Describe what you see
Call or message us on WhatsApp and tell us where the damp or leak is and what surface needs waterproofing: a roof, a foundation or a damp wall.
- 2
We identify the right system
Based on the surface type, its position and its exposure to water, we direct you to the system that suits it, whether bitumen rolls, a membrane or a cementitious coat.
- 3
Preparing the surface
The quality of any waterproofing layer depends on what lies under it: the surface is cleaned, dried and its cracks and joints are sealed before any material is applied.
- 4
Application and the critical details
Joints, edges, the parapet and the drain outlets are where water enters first. Careful work at these points is what separates waterproofing that holds from waterproofing that has to be redone.
Relax, the right surface gets the right system
- Bitumen rolls, membranes and cementitious coats for each situation
- We start with surface preparation before any waterproofing layer
- We give joints and edges the full attention they need
- We take your request by phone call or WhatsApp message
- The cost depends on the surface condition and area
The service in Al Badriyah District
Homes in a district like Al Badriyah often have flat roofs with tanks and drains, and walls exposed to the temperature swings between night and day in Al-Ahsa. These swings cause small cracks that grow over time and become entry points for water and damp. Stains may appear on ceilings or damp on walls. Work starts with a close inspection of cracks, joints and damaged areas, then surfaces are cleaned and prepared before bitumen or membrane is applied. What is found in the first inspection determines which type of protection is needed.
Al Badriyah District is a district in Al-Ahsa governorate in the Eastern Province, close to Imam Muhammed Ibn Saud Islamic University District, Al Majidiyah District and Al Quds District.
Fine cracks on roofs and walls are checked first, as water finds its easiest way through them.
Our portfolio
What our customers say
- ★★★★★
شغلهم كويس وناس ممتازه في اسرع وقت
- ★★★★★
ممتاز والخدمة ان شاء الله تكون قد التوقعات
- ★★★★★
شكرا على التواصل وصلو في اسرع وقت ممكن
Reviews are shown as the customers wrote them, in Arabic.
Questions about Bitumen & membrane insulation in Al Badriyah District
Bitumen rolls are made from a tar-based material reinforced with fibres, fixed by heat or adhesive, and are most common on flat concrete roofs. Plastic membranes are sheets stretched across a surface and joined at edges and seams. The choice depends on the shape of the surface, its heat exposure and how much it moves.
Bitumen rolls suit flat and slightly sloped concrete roofs, tanks and bathrooms. Cold-applied bitumen suits foundations and places where a flame is not practical, as well as smaller areas.
The flat area in the middle of a roof rarely fails first. Water finds its way at the seam between two rolls, at the edge where the layer meets the parapet or at the drain outlet. Those points need a different fixing method and greater care in the work.
Yes. A cementitious waterproof coat is mixed as a slurry and applied to concrete and masonry, blocking water through the pores. It suits tanks, concrete walls, bathrooms and surfaces that do not move significantly. It is not suited to surfaces that expand and contract noticeably, as it can crack under that movement.
Foundations and buried walls face moisture from the ground and water pressure from outside. If the waterproofing is applied to a dirty, wet or uneven surface, the layer detaches from behind over time and water returns. Preparing the surface and treating cracks before application is what makes the layer bond and stay.
Some materials overlap, such as cold bitumen and cementitious coats, but a bathroom floor has its own demands: strong adhesion to tiles and concrete in a small area under constant moisture. A roof faces heat and thermal expansion. So even when materials overlap, the system choice changes with the location and its conditions.
Tell us where the surface is: a roof, a foundation, a bathroom or a tank. Describe its condition: visible damp, cracks or an existing old layer. These details help us guide you to the right system and explain what the cost depends on. The more clearly you describe it, the clearer the answer we can give.
Call when you see a damp stain on ceiling or wall, or notice cracks on the roof or outer walls. Tell them where the stain is and whether it worsens after rain, and send a photo on WhatsApp.
No, some leaks need flexible membranes or a mix of bitumen and membrane. The first inspection of cracks and surface condition decides which system suits each case.
More services in Al Badriyah District
Bitumen & membrane insulation in nearby areas
