From your call to the finished layer
- 1
Tell us what you see
Call or message us on WhatsApp and describe what you want insulated: a roof, a wall, metal sheets or a hangar, and what you have noticed in terms of heat or damp.
- 2
Checking the surface before spraying
Foam is not sprayed onto a wet or crumbling surface: the surface is checked first and any cracks or damaged areas are treated before the work begins.
- 3
Spraying and expansion
The liquid foam is sprayed onto the prepared surface and expands to fill joints, corners and the areas around drains and the parapet without leaving any gaps.
- 4
The protective finish coat
Foam is naturally sensitive to ultraviolet light, so a protective coat is applied over it to shield the surface and prevent it breaking down over time.
Foam insulates from inside and outside at once
- A seamless layer with no joints that weaken the insulation
- Acts as a thermal insulator and a water barrier at the same time
- Suits concrete roofs, metal surfaces and outside walls
- Fills cracks, corners and areas around roof drains
- We take your request by phone call or WhatsApp message
The service in Al Badriyah District
In a district like Al Badriyah, flat roofs on homes are the main way heat enters, so the top rooms become very hot by midday. The roof usually has a parapet round the edge, joints between concrete sections, water tanks on the roof and rain drain channels, all of which are weak points. Sprayed foam covers all of this in one solid layer without needing to be cut into panels. Before spraying starts, the roof is checked to ensure there are no deep cracks or pooled water, because the base must be ready.
Al Badriyah District is a district in Al-Ahsa governorate in the Eastern Province, close to Imam Muhammed Ibn Saud Islamic University District, Al Majidiyah District and Al Quds District.
The check focuses on joints, drains and corners, because water and heat enter from these points first.
Our portfolio
What our customers say
- ★★★★★
شغلهم نظيف وسريعين ومحترمين الله يعطيهم العافيه
- ★★★★★
شغلهم ميه ميه يشكرو عليه
- ★★★★★
شركة ممتازة تستحق التعامل معها بشكل مستمر
Reviews are shown as the customers wrote them, in Arabic.
Questions about Foam insulation (polyurethane) in Al Badriyah District
Boards are cut and fixed, leaving gaps at joints, corners and around pipes. Liquid foam is sprayed and expands to fill those areas naturally, leaving no weak points. That is what makes foam a suitable external insulator for roofs with complex details.
It is both: its closed structure resists water and insulates against heat in a single layer. However, the protective coat over it is necessary because exposed foam breaks down in sunlight and gradually loses both properties.
Foam suits flat concrete roofs, metal sheets and corrugated panels, and exterior concrete or block walls. The common condition is that the surface must be dry and sound before spraying, otherwise the foam does not adhere properly.
Foam exposed to the sun is affected by ultraviolet light: its surface crumbles, yellows and loses its strength over time. The finish coat blocks those rays and keeps the foam solid and intact. It is part of any external foam insulation job and cannot be left out.
If the heat comes from above and you feel it on the top floor, the roof is the most likely source. If a particular room is hotter than others even though it is not directly under the roof, the outside wall facing the sun may be the cause. Both can apply at the same time.
Polyurethane foam is a thick layer that expands after spraying, insulates against heat and resists water. Polyurea is a thin hard coat sprayed to form a flexible waterproof skin without adding meaningful thermal insulation. The first suits you when you want both together; the second when you want a tough waterproof skin on the surface.
Yes, foam is sprayed under the metal roof sheets in hangars and warehouses, reducing the heat that builds up inside and treating condensation on the inner face of the sheets. The large roof area and the height make this work different from insulation in homes.
We check for cracks and joints, parapet corners and tank positions and drains, and look for damp in the base and any signs of old or new leaks.
Foam greatly reduces heat entering through the roof because it is a continuous insulating layer with no gaps, but the first check decides the extent of the problem and the right solution.
More services in Al Badriyah District
Foam insulation (polyurethane) in nearby areas
