From your call to the finished layer
- 1
Tell us what you see
Call or message us on WhatsApp and describe what you want insulated: a roof, a wall, metal sheets or a hangar, and what you have noticed in terms of heat or damp.
- 2
Checking the surface before spraying
Foam is not sprayed onto a wet or crumbling surface: the surface is checked first and any cracks or damaged areas are treated before the work begins.
- 3
Spraying and expansion
The liquid foam is sprayed onto the prepared surface and expands to fill joints, corners and the areas around drains and the parapet without leaving any gaps.
- 4
The protective finish coat
Foam is naturally sensitive to ultraviolet light, so a protective coat is applied over it to shield the surface and prevent it breaking down over time.
Foam insulates from inside and outside at once
- A seamless layer with no joints that weaken the insulation
- Acts as a thermal insulator and a water barrier at the same time
- Suits concrete roofs, metal surfaces and outside walls
- Fills cracks, corners and areas around roof drains
- We take your request by phone call or WhatsApp message
The service in Ash Shi’bah
In a district like Ash Shi'bah, flat roofs are the primary cause of heat in the rooms above. A roof usually carries a parapet and drains, and may have a tank, each creating a joint where hot air and water can enter. Sprayed foam covers these joints and corners with one continuous layer, without being cut into separate panels. Before spraying, the roof is fully checked to ensure there are no cracks, damp or loose material, because any roof fault will affect insulation quality.
Ash Shi'bah is a district in Al-Ahsa governorate in the Eastern Province, close to Al Qurayn, Julayjilah and Ash Shuqayq.
Foam is sprayed on a sound roof, and the first check identifies any cracks or weak joints that must be repaired before spraying.
Our portfolio
What our customers say
- ★★★★★
شغلهم نظيف وسريعين ومحترمين الله يعطيهم العافيه
- ★★★★★
شغلهم ميه ميه يشكرو عليه
- ★★★★★
شركة ممتازة تستحق التعامل معها بشكل مستمر
Reviews are shown as the customers wrote them, in Arabic.
Questions about Foam insulation (polyurethane) in Ash Shi’bah
Boards are cut and fixed, leaving gaps at joints, corners and around pipes. Liquid foam is sprayed and expands to fill those areas naturally, leaving no weak points. That is what makes foam a suitable external insulator for roofs with complex details.
It is both: its closed structure resists water and insulates against heat in a single layer. However, the protective coat over it is necessary because exposed foam breaks down in sunlight and gradually loses both properties.
Foam suits flat concrete roofs, metal sheets and corrugated panels, and exterior concrete or block walls. The common condition is that the surface must be dry and sound before spraying, otherwise the foam does not adhere properly.
Foam exposed to the sun is affected by ultraviolet light: its surface crumbles, yellows and loses its strength over time. The finish coat blocks those rays and keeps the foam solid and intact. It is part of any external foam insulation job and cannot be left out.
If the heat comes from above and you feel it on the top floor, the roof is the most likely source. If a particular room is hotter than others even though it is not directly under the roof, the outside wall facing the sun may be the cause. Both can apply at the same time.
Polyurethane foam is a thick layer that expands after spraying, insulates against heat and resists water. Polyurea is a thin hard coat sprayed to form a flexible waterproof skin without adding meaningful thermal insulation. The first suits you when you want both together; the second when you want a tough waterproof skin on the surface.
Yes, foam is sprayed under the metal roof sheets in hangars and warehouses, reducing the heat that builds up inside and treating condensation on the inner face of the sheets. The large roof area and the height make this work different from insulation in homes.
If top rooms are very hot in summer and uncomfortable despite ventilation, the roof may need insulation. The first check will reveal any cracks or joints letting heat in.
Tell them that rooms under the roof heat up quickly, whether you see damp stains on the ceiling, and whether the roof has a tank, drains or visible joints. A photo of the roof from outside helps with assessment.
More services in Ash Shi’bah
