What shinko insulation includes
- Checking the sheets and identifying open laps and bolt holes before spraying
- Cleaning the surface, treating rust and securing loose panels to prepare for foam
- Spraying polyurethane foam onto the sheets so it flows into laps and holes and sets as a seamless layer
- Applying a finish coat over the foam to protect it from sunlight and breakdown
- Treating sun-facing shinko walls in the same way when that is part of the job
- Answering your questions about corrugated-sheet (shinko) insulation before the work starts
From your call to an insulated roof
- 1
Tell us what you have
Call or message us on WhatsApp and describe the sheet area, whether the problem is heat, leaks or both.
- 2
Preparing the surface
The sheets are cleaned, any loose panel is secured and rust is treated before spraying, because the foam layer needs a sound surface under it.
- 3
Spraying the foam
Foam is sprayed across the sheets in steady passes, expanding to fill laps and holes and setting as a continuous layer that insulates against heat and resists rain.
- 4
The protective coat
A finish coat is applied over the foam to protect it from sunlight and wear, because bare foam breaks down over time under ultraviolet rays.
Why foam suits metal sheets
- It flows into laps and bolt holes, leaving no gap
- A seamless layer with no joints or exposed edges
- Insulates against heat and reduces drum noise together
- We treat annexes, car shelters and corrugated roofs
- We take your request by phone call or WhatsApp message
The service in As Sunaidah District
Corrugated-sheet roofs are common on homes in a district like As Sunaidah, trapping heat and moisture directly underneath. Sprayed foam fills the gaps between the sheets and the roof base, forming a continuous barrier against heat and water. The team checks the sheet layout, joints and any existing leaks before starting, because the surface must be stable and sheets firmly fixed before spraying. Foam cannot repair a broken sheet or weak joint, but it provides real protection to the roof once what needs fixing is done.
As Sunaidah District is a district in Al-Ahsa governorate in the Eastern Province, close to Munifah District, Ar Rafiah District and Al Marbidia District.
The joints between corrugated sheets are where water and hot air enter first, and they need special care during insulation.
Our portfolio
What our customers say
- ★★★★★
شكرا على التواصل وصلو في اسرع وقت ممكن
- ★★★★★
شركة ممتازة تستحق التعامل معها بشكل مستمر
- ★★★★★
شركه ممتازه
Reviews are shown as the customers wrote them, in Arabic.
Questions about Corrugated-sheet (shinko) insulation in As Sunaidah District
Spraying works from both sides depending on the situation. Spraying underneath insulates against heat, reduces noise inside the annex and stays protected from the sun by the sheets above. Spraying on top adds waterproofing and covers laps and holes. When the problem is both heat and leaks, the job often involves both sides.
The lap between two overlapping sheets is not automatically tight: heat expands the metal and cold contracts it, so laps move and small gaps open over time. Bolt holes also widen with repeated expansion. These entry points are not visible to the eye but they let water through, especially when rain comes with wind.
Yes. The foam bonds to the sheet and absorbs the vibration that turns raindrops into a drumming sound. The seamless layer stops the sheet resonating the way it does when bare. This is one of the noticeable changes for anyone who uses the annex or shelter regularly.
It suits the walls too. A shinko wall facing the sun absorbs heat and passes it straight inside, and its laps and bolt holes let in air and moisture just like the roof. Foam is sprayed onto the wall in the same way and a protective coat is added over it.
Tell us whether the problem is heat, leaks or both, whether the sheets are on the roof or the walls or both, and whether you can see rust, open laps or loose bolts. The clearer your description, the better we can work out what the surface needs before we visit.
Foam is sprayed onto the sheets after checking that they are firmly fixed and sound, but if a sheet is broken or poorly sealed, it must be repaired first, because foam cannot fix underlying faults.
Say the ceiling gets very hot in summer or you hear rain noise on the sheets, whether the sheets are old or new, and send a photo showing the sheet condition and joints on WhatsApp if possible.
More services in As Sunaidah District
Corrugated-sheet (shinko) insulation in nearby areas
