What tank cleaning and waterproofing includes
- Fully emptying the tank and removing sediment and residue from its walls and base
- Rinsing the inner walls until the surface is clean and ready for inspection
- Checking the tank walls, base and joints for cracks or damage to the inner lining
- Treating cracks and joints and preparing the surface before any waterproofing material is applied
- Applying the right waterproofing layer to the walls, base, edges and corners
- Giving special attention to the joints between walls and base, which are often the most vulnerable points
From your call to a sealed tank
- 1
Describe what you see
Call or message us on WhatsApp and tell us the tank type, where it sits and what you have noticed, whether a leak or damage to the inner surface.
- 2
Emptying and cleaning the tank
The tank is fully emptied, then the sediment and residue clinging to its walls and base are removed, and it is rinsed until the surfaces are clean and dry.
- 3
Repairing cracks and preparing the surface
Cracks and joints are treated before any coat is applied, because a waterproofing material does not bond to a cracked or wet surface. A good layer starts with a surface that is ready.
- 4
Applying the waterproofing layer
The right waterproofing material for the tank, such as epoxy or bitumen, is applied to the walls, the base and the corner joints, with careful attention to edges and seams.
Why combine cleaning and waterproofing in one job
- Waterproofing over a dirty surface separates quickly
- We treat cracks before any coat is applied
- We check all the tank walls while cleaning
- We use waterproofing materials suited to water tanks
- We take your request by phone call or WhatsApp message
The service in Muraytibah
In a small settlement like Muraytibah, each home relies on a tank to store fresh or brackish water from local wells. Ground water in Al-Ahsa usually contains salts that deposit on inner walls and corrode metal tanks. High humidity and intense summer heat speed up lining and joint failure. Work starts by emptying the tank and carefully cleaning the body, floor, corners and joints of deposits, rust and algae, then it is left to dry completely. After inspection, it is decided whether epoxy or bitumen waterproofing is needed.
Muraytibah is a small settlement in Al-Ahsa governorate in the Eastern Province, close to Sudah, Al Ghuwaybah and At Taraf.
A tank holding brackish water corrodes from inside faster, so inspection focuses on the tank floor and lower walls.
Our portfolio
What our customers say
- ★★★★★
شركه ممتاز شغلهم كويس ويعطيهم العافيه
- ★★★★★
ممتاز والخدمة ان شاء الله تكون قد التوقعات
- ★★★★★
شغلهم ميه ميه يشكرو عليه
Reviews are shown as the customers wrote them, in Arabic.
Questions about Tank cleaning & waterproofing in Muraytibah
Cleaning is a necessary step before waterproofing. The material needs a clean, dry surface to bond to. Any sediment, algae or residue between the wall and the coat causes it to separate quickly. Waterproofing alone without prior cleaning does not solve the problem.
Epoxy is a resin that hardens after application and forms a rigid layer that resists water and wear; it is often used to line indoor water tanks. Bitumen is a flexible rubber-like material or comes as a rolled membrane fixed to the surface, and suits different conditions. The choice depends on the tank type and the state of its walls.
It is not advisable. A crack in a tank wall moves with heat expansion and contraction, and any coat applied over it without treatment will crack again at the same spot. Treating cracks and joints before applying the waterproofing is the step that keeps the layer in place over time.
Yes, full emptying is necessary for both steps. The walls and base cannot be cleaned properly with water still inside, and a waterproofing material cannot be applied to a wet surface. After the coating is applied, the surface needs enough time to dry before the tank is refilled.
Tell us the tank type, ground or overhead, and whether it is concrete or plastic, and what you have noticed: a leak from a wall or the base, a crack in the inner lining, or an odour in the water. The clearer the details, the better we can judge what the tank needs before we arrive.
Ground water in Al-Ahsa contains salts and may be brackish, which causes fast rust and corrosion. A layer of epoxy or bitumen waterproofing protects the tank from rust and stops water leaking through cracks and joints.
Deposits, salts and rust build up and perforate the tank walls, the leak becomes large and the water loses its purity, and rust may reach spots that are hard to repair. Early cleaning stops this decline.
More services in Muraytibah
Tank cleaning & waterproofing in nearby areas
