What roof heat insulation includes
- Checking the concrete roof condition to identify what needs treating before insulation
- Finding cracks and joints that need repair before the layer goes on
- Preparing, cleaning and levelling the surface so the layer bonds properly
- Applying sprayed polyurethane foam or epoxy coating according to the roof condition
- Covering edges, joints and the base of the parapet to complete the insulation
- Treating any water leak found during inspection before the heat insulation is finished
From your call to an insulated roof
- 1
Tell us what you feel
Call or message us on WhatsApp and describe which floor gets hot and which rooms are affected, and we will decide with you what needs to be checked.
- 2
We inspect the roof first
We check the roof condition before anything else, because a roof with cracks or standing water needs waterproofing before the heat-insulating layer goes on.
- 3
We prepare the surface
The job involves cleaning the surface and levelling what needs levelling, because a layer only works as it should on a clean and ready surface.
- 4
We lay the heat-insulating layer
We choose between sprayed polyurethane foam and epoxy coating according to the roof condition and what is needed, and we cover the whole area including the edges and joints.
An insulated roof makes a difference in the rooms below
- We inspect the roof before insulating to choose the right layer
- Polyurethane foam covers edges, joints and corners
- Epoxy is a hard coating that reflects heat and protects the surface
- We treat cracks and leaks before the heat-insulating layer goes on
- We take your request by phone call or WhatsApp message
The service in ’Uray’irah
Homes in a village like 'Uray'irah usually have flat roofs with rooftop tanks, and the top-floor room sits directly under the roof, so it heats first. The roof often has a parapet, drains and covers, each a joint where heat and damp enter. Sprayed foam follows these shapes without cutting panels, ensuring full coverage. The existing surface is checked first, because loose or damp material under foam will remain a problem.
'Uray'irah is a village in Al-Ahsa governorate in the Eastern Province, close to Umm Tali, Umm Rubay'ah and Umm al Hamam.
Around the tank base and parapet, foam needs the most attention, because water pools there first when rain comes.
Our portfolio
What our customers say
- ★★★★★
ممتاز والخدمة ان شاء الله تكون قد التوقعات
- ★★★★★
شكرا على التواصل وصلو في اسرع وقت ممكن
- ★★★★★
شركه ممتاز شغلهم كويس ويعطيهم العافيه
Reviews are shown as the customers wrote them, in Arabic.
Questions about Roof heat insulation in ’Uray’irah
Heat insulation aims to stop the sun's heat passing from the concrete roof into the rooms below, which shows in the top floor in summer. Waterproofing aims to stop water entering through cracks and joints. A roof often needs both, and inspection decides which comes first.
A layer on its own does not seal cracks; it goes on a ready surface. If the roof has cracks or areas that have held water before, treating them comes before the heat-insulating layer, otherwise the problem stays under the new layer.
Polyurethane foam is a sprayed foam layer that fills edges, corners and joints and insulates well. Epoxy is a resin that is applied as a coat and hardens, reflecting heat and protecting the concrete. Choosing between them depends on the roof condition and what it needs.
Roof heat insulation treats the transfer of heat through the concrete into the rooms below. Wall dampness has its own causes, often water entering through joints or cracks in the wall or roof. Inspection identifies the source of the dampness before any treatment.
Heat insulation suits exposed concrete roofs where heat transfer is the main problem. If the roof has wide cracks, standing water or a badly worn old layer, the work starts with assessing the roof condition and deciding what to treat first before the right heat-insulation method is chosen.
We check the roof for cracks, joints, parapet condition and drains, and for damp under the old layer, because foam is sprayed only on a sound, dry surface.
It means the roof absorbs heat during the day and releases it slowly at night. Foam insulation reduces this absorption, so the room cools faster and needs less air conditioning.
More services in ’Uray’irah
